Home

Eagletree Products


EagleTree V3 E-Logger

 

 

£44.99 ELG-CAV3
Bantam-301DX Multi charger

Kit Contents...

1 off -
V3 E-Logger
1 off - USB Cable
1 off - Software CD & Digital User Manual

Specifications

 

Eagletree V3 E-Logger Suitable for logging all flight data for;  Planes -  Jets - Heli's - Electrics.

See typical large model set-up

ELG-CAV3

Back to Top

Power Panel Display

 

 

£22.99 ELPP3
Bantam-301DX Multi charger

 

Specifications

 

This ultra thin LCD display connects to the V3 E-Logger  with the included 11" data cable, and lets you get your max and live data displayed without a PC.        Set up allows for real time sensor display or max & min flight parameters.

ELPP3

Back to Top

Optical RPM Sensor

 

 

£8.99 ORPM
Bantam-301DX Multi charger

 

 

This Optical RPM Sensor enables you to log the RPM of your RC model when connected to a Micro e-logger system. The Sensor contains an Infra Red source and an Infra Red detector and measures the RPM via reflected light.

Optical RPM Sensor
RPM Range approx 100 to 50,000+ RPM
Length of Wires 15cm / 6 inchs

ORPM

Back to Top

Air Speed Module

 

 

£18.99 ELASV3
Bantam-301DX Multi charger

 

 

 


Includes Pitot Tube and Hose.
Air Speed Module
Airspeed Range approx 9 - 200 MPH

ELASV3

Back to Top

Temperature Loop

 

 

£6.99 NTCL

 

 

 

Log the temperatures of your RC model with this NTC thermistor loop temperature sensor. Wraps around your battery or other location and can measure temperatures of 0 to 220°C. Ideal for Cylinder Heads etc.

Micro Temperature Probe Sensor
Temperature Range 0 to 220°C (0 to 434°F)
Length of Wires 15cm / 6 inchs

NTCL

Back to Top

Altimeter

 

 

£18.99 EALT

 

 

 

High resolution Altimeter measures Altitude from 0-8000 feet (0-2400m) with 3 foot (1 meter) or higher resolution.

Daisy Chains with all other MicroPower Sensors!

EALT

Back to Top

Servo Current

 

 

£18.99 EASCRT

 

 

 

Find out how much current your servo or other low current devices are drawing. Plugs into your MicroPower and servo (or reciever battery/BEC) to log current from 0-5 Amps continuous, with 0.01 Amp resolution.

Daisy Chains with all other MicroPower Sensors!

EASCRT

Back to Top

Spectrum Receiver Data

 

 

£3.96 ESDLC

 

 

 

Spektrum/JR(TM) Interface Cable for Micro e-Logger V3 and Pro Data Recorder Systems...

Now use your Eagletree Logger to see Spektrum/ JR Rx holds/failsafes, lost frames, and antenna fades (up to 4 antennas) on your PowerPanel (micro e-Logger) or Seagull (Pro Data Logger), or logged for later review!

Micro e-Logger ...
Connects between your Spektrum "FlightLog" data port and the eLogger V3's GPS port. Use a servo Y cable to use your FlightLog display simultaneously! NOTE: make sure your RX has the data port before ordering.

Pro Data Recorder...
Connects between your RX's "Flight Log" data port and the Pro Recorder's GPS port. Use a servo Y cable to use your FlightLog display simultaneously! NOTE: make sure your RX has the data port before ordering.

 

ESDLC 

Back to Top


Temperature Probe

 

 

£6.84 NTCLP

 

 

 

The Micro Temperature Probe Sensor is perfect for measuring temps of your batteries and ESC.
The NTC thermistor probe can be fixed to your battery or other location and can measure temperatures of 0 to 120°C (250°F).
Up to two temperature sensors can be connected to the MicroPower simultaneously.

Micro Temperature Probe Sensor
Temperature Range 0 to 220°C (0 to 434°F)
Length of Wires 15cm / 6 inchs

NTCL

Back to Top

 


Airspeed Microsensor V3... or StandAlone!

 

 

£27.99 ESMAS 

 

 

 

Works as a standalone unit or connects to any of our eLogger products for full logging and graphing of your flight’s speed or altitude!

For standalone mode, simply plug the sensor into a spare receiver channel or small battery (3V to 16V) and fly your model. Then, when you land, your maximum airspeed will display on the built-in 7 segment LED. For example, if your max airspeed was 281 MPH, the unit will display “2 – 8 - 1”  repeatedly. No configuration, additional equipment, or computer required!

  • Measures from approximately 2 MPH to 350 MPH
  • Weight 4 grams (0.15 oz)
  • Includes Pitot Tube
  • Accessible static port
  • Pre-calibrated – no user calibration required
  • Metric or English units

 

ESMAS

Back to Top

 


Altimeter  Microsensor V3... or Standalone!

 

 

£24.99 ESMALT

 

 

 

Works as a standalone unit or connects to any of our eLogger products for full logging and graphing of your flight’s speed or altitude!

For standalone mode, simply plug the sensor into a spare receiver channel or small battery (3V to 16V) and fly your model. Then, when you land, your maximum altitude will display on the built-in 7 segment LED. For example, if you flew to 281 feet, the unit will display “2 – 8 - 1”  repeatedly. No configuration, additional equipment, or computer required!

  • Lowest cost standalone Altimeter on the market!
  • Aproximately 3 foot (1 meter) resolution
  • Weight 4 grams (0.15 oz)
  • Precalibrated – no user calibration required
  • Accessible static port
  • Metric or English units

 

ESMALT

Back to Top